P V C 地 板 施 工

　　本工程設計采用PVC卷材地板，自流平基層。本工藝控制重點為自流平除氣(水氣和空氣)和PVC卷材地板平整度及無縫焊接。

　　自流平：自流平漿料傾倒入地坪，任其像水一樣流平開來進行自動找平，必須使用專用齒口自流平子母刮板加以來回橫向、豎向疏導。

　　在自流平初凝前須穿釘鞋走入自流平地面，用專用放氣滾筒滾扎地面以排除因混合時帶入的空氣，避免氣泡，麻面及接口高差。養護1—2天即可鋪設。

　　PVC卷材地板平整度：PVC地板正確的存放方法為豎直存放，不正確的儲存方法會導致PVC地板鋪貼時形成波浪型，且容易使PVC地板邊部損傷，影響安裝效果。把切割好的PVC地板平放在地面上，仔細檢查PVC地板表面，防止出現質量問題。PVC地板與PVC地板之間不應預留任何空間。鋪貼完一個空間，膠水未完全干固前，再用大鐵磙推壓地面，使已貼好的地板更加平整，或用沙袋壓實。

　　PVC地板熱力焊接：熱力焊接是連接PVC地板接縫的最佳方法。熱力焊接應在鋪貼PVC地板工作完成24小時后進行。用專業開槽刀或專業自動開槽機在地板接縫處開出“U”型焊槽。槽的深度約為地材的三分之二，但不可超過2mm。用專業焊機把地材專用焊線焊接在“U”型槽內。待焊條溫度略降時，用專用鏟刀把焊線剩余凸起部分鏟掉三分之二，當焊線完全冷卻后，再用鏟刀把焊線剩余凸起部分完全鏟掉。焊線一定要分兩次鏟除